ONYX Crete TC
Heavy Duty Polyurethane Cement Top Coat
General Product Description
ONYX Crete TC is a three-component polyurethane concrete floor system. Its unique formulation makes it ideal for many harsh environmental conditions. It is especially suited to handle high temperature sanitary wash down and steam where thermal cycling is present. In addition, ONYX Crete TC has excellent chemical resistance. It is applied as a top coat over the ONYX Crete SL base coat. ONYX Crete TC is USDA accepted for use in federally inspected food facilities.
Advantages
- Resistant to Thermal Shock
- -50 to 250 Degrees F Temperature Range
- Ideal for CIP (Cleaning-In-Place) applications
- Handles Severe Impact Conditions
- Skid-Resistant Surface
- Seamless Flooring System
- Essentially Odorless
- Withstands Heavy Forklift Traffic
- Chemical Resistant
- Abrasion Resistant
Product Data
| Ratio: | 1 To 1 To 1 |
| V.o.c.: | 0 G/L |
| Application Temp: | 65-90°F And 5° Above Dew Pt. |
| Thinning: | Not Required |
| Pot Life: | 6-8 Minutes |
| Working Time: | 10-12 Minutes |
| Cure Time: | 8-10 Hours (Walking) 24 Hours (Light To Medium Traffic) 48 Hours (Heavy Traffic) |
| Shelf Life: | 6 Months |
| USDA Food And Beverage: | Meets Requirements |
Cure time, pot life, and working time are based on a slab temperature of 70-75 F°, and will change accordingly as temperature changes.
Applications
- Food Processing
- Beverage Plants
- Dairies
- Bakeries
- Freezers and Cold Storage
- Fryer Lines
- Meat Packing and Poultry
- Commercial Kitchens
- Ovens
- Wash Downs
- Wineries
- Breweries”
Physical Properties
| Property | Value | Reference |
|---|---|---|
| Compressive Strength | 8,200 psi | ASTM C 579 |
| Flexural Strength | 2,375 psi | ASTM C 580 |
| Tensile Strength | 920 psi | ASTM D 307 |
| Bond to Concrete | 350 psi concrete fails at this point | ASTM D 4541 |
| Coefficient of Thermal Expansion | <- 12.6 X 10 | ASTM C 531 |
| Water Absorption | .10% maximum | ASTM D 413 |
| Linear Shrinkage | .20% maximum | ASTM C 531 |
| Impact Resistance | 16 ft. lb. – no failure | Mil-D-3134H |
| Anti-Microbial | Passes | G-21 |
| Coefficient of Friction | Passes | ASTM D 2047 |
| Modulus of Elasticity | 1.8 X 10 | ASTM C 580 |
| Temperature Rating | 230°F |
CHEMICAL RESISTANCE
| Acetic Acid 30% | R |
| Ethanol | R |
| Alcohol, Isopropyl | SS |
| Aluminum Hydroxide | R |
| Citric Acid | R |
| Copper Chloride | R |
| Diesel | R |
| Ferric Acid | R |
| Hydrochloric Acid 37% | R |
| Nitric Acid 30% | SS |
| Phosphoric Acid | SS |
| Skydrol R | R |
| Sodium Bisulfate | R |
| Sodium Chloride | R |
| Sodium Hydroxide 50% | R |
| Sulfuric Acid 50% | R |
Note: The above guide is based on 7 days exposure of the listed chemical at 72 degrees F (22 degrees C)
Key: R = Recommended, SS = Splash and Spill, NR = Not Recommended. Above chart serves as a guideline only. Samples will be furnished upon request for testing.
Concrete Preparation
- Before the coating is applied, the concrete must be:
- Clean – Contaminants removed
- Profiled – Surface mechanically prepared
- Sound – Cracks repaired
Mechanical methods are required for preparing concrete prior to coating application. Shot-blasting, diamond grinding, scarifying, and scabbling are all acceptable methods. The concrete profile should be a minimum of a CSP 5.
Mixing
The standard mix ratio of ONYX Crete TC is, 1 part of A, to 1 part of B, to 1 bag of Part C. Mix this with a drill and jiffler mixer.
- In an empty 6 gallon bucket (5-gallon buckets do not leave much room for the mix), pour in a gallon of Part A and a gallon of Part B. If pigment is on the side, add 8 oz. of pigment. Mix with jiffler mixer for 30-45 seconds until uniform.
- Add 1 bag of Part C and mix with jiffler for another 20 seconds.
- To remove lumps from the material by using a strainer in a clean, dry bucket, and pour the mix into it, filtering the resin. Then immediately apply onto the ONYX Crete SL broadcasted surface
Application Process
ONYX Crete TC is best applied with a standard squeegee. After mixing, immediately dump all of the material out of the bucket and onto the properly prepared concrete.
- Using a chip brush or weenie roller, cut into the edge of the perimeter and tight small spaces, coating it with the resin.
- Use a 18″ wide, 3/8″ nap, non-shedding roller to roll out the resin. The coverage rate should approximately be approximately 160-200 Sq Ft per kit depending on the desired texture and the sand’s grit.”
- After backrolling (north to south) the coating, come back within 3-5 minutes and begin to crossroll (east to west). Keep a wet edge no more than 1 foot for the application.
- The slip-resistant surface will vary depending on the grit size of the aggregate used in the final broadcast.
Color Selection
Refer to the ONYX Crete Color Chart to see available standard colors. Other colors are available at an additional charge.
Cleanup
ONYX Crete TC while in a liquid state may be cleaned up with water and degreaser. Otherwise a strong solvent may be required while ONYX Crete TC is setting up.
Warranty
ONYX products are warranted for 1 year after date of manufacture. Please refer to the ONYX Limited Material Warranty for additional clarification.
Safety
Consult ONYX Crete TC safety data sheet. Avoid ONYX Crete TC contact with eyes and skin. Always wear protective eyeware, clothing, and gloves. Safety always comes first.
Maintenance
Refer to the ONYX Maintenance and Cleaning Guidelines.
PRODUCT LIMITATIONS
Always read the ONYX PRODUCT LIMITATION GUIDELINES prior to installation.